Type airvision

Our series airvision L is an economy construction in sizes ¼“ und 1/8“.

Filter

Compressed air filter in modular design for cleansing the compressed air of humidity (by means of cycloning) and solid particles. Can be flanged on either side for additional airvision equipment. Port sizes G1/8 to G1.

Special-Filters

Compressed air filters in modular design remove almost without residue the smallest remaining particles of water, oil or dirt to 99,999% (for 0,01 ?m).
Port sizes G1/8 to G½.

Pressure Regulators

Compressed air pressure regulators in modular design maintain constant working pressure regardless of pressure fluctuations in the system or of air consumption. Flanging is possible on both sides for adding other airvision equipment. Port sizes G1/8 to G1. Secondary air exhaust (relieving) and almost complete independence of primary pressure. Diaphragm regulator with working pressure ranges 0,5 to 6, 10 and 16 bar. Adjustment can be locked by pressing the handwheel. Gauge can be mounted on back or front.

Important: Use of filter always recommended.

Fog-Lubricators

Compressed air lubricator in modular design add a fine oil fog to the compressed air, providing a constant and reliable lubrication of pneumatically regulated compressed air tools, valves and cylinders etc… Flanging is possible on both sides for adding other airvision equipment.
Port sizes G1/8 to G1. Oil can be refilled under pressure. Needle valve for oil adjustment with high drop constancy over long periods of time.

Recommended oil: Oil containers made of plastic (polycarbonate) are attacked by oil additives, anti-frost or synthetic oils. We therefore recommend normal lubricating oils of approx. 22 to 32cSt at 40°C (in the case of striking tools up to 68cSt). Metal containers should be used for other oils, especially for low-temperature oils. Also recommended is a metal lubricator adjusting cap.

Filter Pressure Regulators

Filters for compressed air and pressure regulators combined in one piece of equipment in modular design to save space. The cleansed compressed air is kept at constant pressure regardless of pressure fluctuations in the system or of air consumption. Secondary air exhaust (relieving) and almost complete independence of primary pressure.

Diaphragm regulator with working pressure ranges 0,5 to 6, 10 or 16 bar. Adjustment can be locked by pressing the handwheel. Gauge can be mounted on back or front side. Additional airvision equipment can be flanged to either side. Port sizes G1/8 to G1.

Maintenance Units

Two-Piece Maintenance Units in block assembly consisting of an airvision filter pressure reducer and fog lubricator. Flanging is possible on either side for additional equipment. Other variations are possible by combination with additional equipment. Port sizes G1/8 to G1.

Three-Piece Maintenance Units – Many variations are possible by combination with other equipment. Port sizes G1/8 to G1.

Distributors wide and narrow

Distributors in modular design are suitable for flanging at any position onto airvision maintenance units. Port sizes G1/8 to G1. They have two outlets (above and below), which are plugged upon delivery.

Distributors With Non-Return Valves

Distributors with a non-return valve in modular design are mounted before the airvision fog lubricator. Removal of unlubricated air is possible through four outlets which are plugged upon delivery. Port sizes G1/8 to G½.

Ball Valves

Ball valves (3/2-way valves) in modular design with relieving for flanging onto airvision maintenance units are especially suitable as a main shut-off valve at inlet. Operation by means of a toggle that turns 90 degrees to switch positions that correspond to the functions:
crosswise = closed, relieving open; parallel = open. Toggle available in lockable model.
Relieving with sintered muffler. Port sizes G1/8 to G½.

Starting Valves

Starting valves or filling valves in modular design serve to raise the pressure gradually in pneumatic systems when they are being started, for example after emergency shut-off. When switched on, throttles release at first only a small orifice. Only when the pressure has reached about 50% of operating pressure is the full orifice opened. In the opposite direction (relieving) the full orifice is opened by means of a non-return valve. In combination with airvision equipment such as the 3/2-way valve or solenoid valve a complete on-and-off unit can be assembled. Port sizes G1/8 to G½.

Solenoid Valves

Solenoid valves (3/2-way valves) in modular design can be used as an alternative to the manually operated ball valve for various voltages as shut-off valves in compressed air systems. The electric connection is made by means of a couplet socket with Pg. Protective system IP 65 according to DIN 40050. The valve is closed when currentless. Port sizes G1/8 to G½.